Page 25 - 江苏全友电气有限公司

CCX-L密集型铜铝复合母线槽 CCX-L密集型铜铝复合母线槽

CCX-L密集型铜铝复合母线槽 CCX-L密集型铜铝复合母线槽
CCX-L Copper-Al Complex Busbar Channel CCX-L Copper-Al Complex Busbar Channel
接头组件 Joint assembly： The two forms: one is the ordinary type, with insulating bolt locking design; another uses the current international
采用两种形式：一种是普通型的，用绝缘螺栓锁紧设计；另一种采用现行国际通用的先进单臂螺栓锁紧 advanced one bolt locking design, namely with torque wrench in the device on the side of the high strength bolt lock,
设计，即只需用力矩板手在装置一边对高强螺栓进行锁紧，无需其他辅助工具。接头器内也可配备单臂双头 without other auxiliary tools. The connector can also be equipped with one arm double-headed bolt torque, when
力矩螺栓，当锁紧力矩达到定值，螺栓的一个端头将会自动脱落，螺栓尚有另一螺栓头留作将来维修或装拆 the locking torque reaches a fixed value, an end head bolt bolt will automatically fall off, there is another bolt head is
用，操作时无须采用力矩扳手。 reserved for future repair or removal, operation without using torque wrench.
接头器全理的结构设计，可使母线各单元能从上面轻松插入；两侧压力板内部的大面积球型垫圈使整个接 Structure design of full physical connector, can make each unit from above bus can easily insert; washers ball
头内部的接触面压力均匀、防止震动并使整个装置在各种环境内达到稳定的电气连通。每种相同规格的接头 type large area internal pressure plate on both sides of the contact surface between the pressure of the whole joint
器均具有互换性，使母线系统在安装中灵活使用。 internal uniform, to prevent vibration and to make the whole device to achieve stable electrical connection in a variety
The two forms: one is the ordinary type, with insulating bolt locking design; another uses the current international of environments. Connector each the same specifications are interchangeable, the bus system for flexible use in the
advanced one bolt locking design, namely with torque wrench in the device on the side of the high strength bolt lock,
without other auxiliary tools. The connector can also be equipped with one arm double-headed bolt torque, when installation.
the locking torque reaches a fixed value, an end head bolt bolt will automatically fall off, there is another bolt head is
reserved for future repair or removal, operation without using torque wrench. L垂直+始端组合弯头：
Structure design of full physical connector, can make each unit from above bus can easily insert; washers ball L vertical + terminal combined elbow:
type large area internal pressure plate on both sides of the contact surface between the pressure of the whole joint L垂直+始端组合弯头一般用于母线槽十分接近低压柜并且没有足
internal uniform, to prevent vibration and to make the whole device to achieve stable electrical connection in a variety
of environments. Connector each the same specifications are interchangeable, the bus system for flexible use in the 够空间安排标准始端和L垂直弯头的地方；
installation. 始端母线提供与低压配电柜、变压器低压侧、始端进线箱及其他
配电设备的直接连接；每个弯头配置一套接头组件；
铜铝复合导体：200A-2000A为单槽配置；2500A-3500A为双槽
配置；

单槽母线，L1（始端爪长）标准中心长度为0.2米；L2、L3标准
中心长度为0.5米；
双槽母线，L1（始端爪长）标准中心长度为0.2米；L2、L3标准中心长度为0.5米；
始端爪间标准间距A长度0.1米；所有参数长度可根据现场的实际情况设定。
L vertical + terminal combined elbow for busbar is very close to the low voltage switch cabinet and not enough
space for standard beginning and L vertical elbow;
Initial end bus with low voltage power distribution cabinet, transformer low voltage side, beginning the inlet box
and other distribution equipment directly connected; each bend a joint assembly;
接头组件 Joint assembly： Copper and aluminum composite conductors: 200A-2000A as the single slot configuration; 2500A-3500A is a
采用两种形式：一种是普通型的，用绝缘螺栓锁紧设计；另 double tank configuration;
一种采用现行国际通用的先进单臂螺栓锁紧设计，即只需用力矩 Single busbar, L1 ( proximal claw length ) standard center is 0.2 meters in length; L2, the standard L3 length of
板手在装置一边对高强螺栓进行锁紧，无需其他辅助工具。接头 0.5 meters;
器内也可配备单臂双头力矩螺栓，当锁紧力矩达到定值，螺栓的 Double bus slot, L1 ( proximal claw length ) standard center is 0.2 meters in length; L2, the standard L3 length of
一个端头将会自动脱落，螺栓尚有另一螺栓头留作将来维修或装
0.5 meters;
拆用，操作时无须采用力矩扳手。
Proximal claw standard A spacing of 0.1 meters in length; all the parameters length can be set according to the
接头器全理的结构设计，可使母线各单元能从上面轻松插
actual situation.
入；两侧压力板内部的大面积球型垫圈使整个接头内部的接触面
压力均匀、防止震动并使整个装置在各种环境内达到稳定的电气
连通。每种相同规格的接头器均具有互换性，使母线系统在安装
中灵活使用。

21 BUSWAY SERIES BUSWAY SERIES 22